Eco-friendly approach for enhancing the floatability of non-metallic components in waste printed circuit boards: Adding gutter oil during dry grinding.

Waste printed circuit boards (WPCBs) are an attractive secondary resource that is challenging to dispose of due to its complexity. Reverse flotation is an effective method to remove non-metallic particles (NMPs) to obtain metals from WPCBs. Nevertheless, the removal of NMPs is usually inadequate in the present flotation practice. Thus, to provide a clean approach to improve the removal efficiency of NMPs, the method of adding gutter oil during dry grinding process was adopted to enhance the hydrophobic sites on the surface of NMPs to improve the floatability. The surface morphology of NMPs was analyzed by SEM, the results show that the rough morphology inhibited the adhesion of bubbles, while water occupied the cracks and pores, making it challenging for collector adsorption, which result in unstable particle-bubble adhesion. The results of FTIR indicate that both NMPs and gutter oil have -CH3, -CH2, -C = O, -C-O functional groups, which promotes the adsorption of gutter oil on the surface of NMPs. The contact angle (CA) results show that the adsorption of gutter oil on the particle surface is conducive to the formation of enhanced CA. Furthermore, the flotation enhancement effect was verified by flotation kinetic experiments. The accumulated floats yield of NMPs conditioned by gutter oil during grinding is increased from 67.05% (NMPs without conditioning) to 95.02%, and the resin recovery is increased by 31.10%. It is demonstrated that dry grinding with gutter oil can strengthen the floatability of NMPs, which provides a potential approach to increase the flotation efficiency of WPCBs.

Enhanced cleaner flotation behavior of non-metallic particles in waste printed circuit boards: From the perspective of particle size.

Flotation is an attractive method for separating the different components of waste printed circuit boards (WPCBs) due to its cleanliness and efficiency. Non-metallic particles (NMPs) with good floatability usually need to be floated, however, it is difficult to achieve complete removal. The effect of particle size on the flotation behavior of NMPs, which is usually ignored in previous studies, is concerned in this paper. Flotation tests and kinetic analysis were carried out to reveal the effect of reagent dosage on flotation characteristics of particles in narrow size fractions. As the fineness decreases, the particles are more likely to be floated. Equally, the finer the particle size, the lower the reagent dosage required to achieve the maximum recovery. For 1-0.5 mm and -0.045 mm, the maximum recovery increased from 42.16% (1500 g/t MIBC) to 97.31% (100 g/t MIBC). Therefore, the feasibility of reducing particle size by grinding to improve floatability was verified. The results show that the reduction of particle size can significantly promote its efficiency of being floated. After grinding treatment, -0.045 mm yields in each size fraction (1-0.5, 0.5-0.25, 0.25-0.125, 0.125-0.074, 0.074-0.045 mm) increased by 22.10%, 28.42%, 30.90%, 64.56%, 89.32%, resulting in an increase of 37.71%, 13.12%, 2.82%, 7.82% and 2.00% in maximum recovery, respectively. It is also proved that the particle size, rather than the resin content, has a more significant effect on the floatability of NMPs.

Advanced utilization of copper in waste printed circuit boards: Synthesis of nano-copper assisted by physical enrichment.

The copper in the waste printed circuit boards (WPCBs) is cleanly recycled by physical methods and presented in the form of nano copper particles by hydrometallurgical, which provides environmental approach to the advanced utilization of metal copper. Copper in WPCBs was first pre-concentrated by gradient enrichment process including gravity separation, mechanical grinding and flotation. The leaching method was then used to dissolve copper from the flotation concentrate in ammoniacal/ammonium salt solutions. Subsequently, reduction treatment was conducted to synthesize nano-copper from leaching solution. The enrichment results of the clean physical separation process show that the grade of copper increased from 16.22% to -38.05% by gravity separation, and the grade of copper further increased to 72.62 % by flotation after dissociation, which avoids overgrinding of low value components. Copper nanoparticles can be prepared effectively, and the recovery of copper in the leaching process reaches 99 %. The particle size of copper nanoparticles obtained by ascorbic acid reduction is tens of nanometers, and the surface of copper nanoparticles is smooth and nearly spherical. The present study proposes an environmentally friendly process of preparing nano-copper from the copper in WPCBs.

Kelp-derived N-doped biochar activated peroxymonosulfate for ofloxacin degradation.

N-doped carbon materials have been proven to be effective catalysts for activating peroxymonosulfate (PMS). Marine algae biomass is rich in nitrogenous substances , which can reduce the cost of N-doping process and can obtain excellent N-doped catalysts cheaply and easily. In this study, kelp biomass was selected to prepare N-doped kelp biochar (KB) materials. The high defect degree, high specific surface area, and participation of graphite N make KB have excellent catalytic degradation ability. The KB degraded 40 mg/L ofloxacin (OFL) close to 100% within 60 min, applied with PMS. Through quenching experiments and electron paramagnetic resonance spectroscopy, the degradation process dominated by non-radical pathways was determined. At the same time, O2·- and 1O2 were closely related, and a significant impact of quenching O2·- on the reaction was observed. The non-radical approach made the system excellent performance over a wide pH range and in the presence of multiple anions. The experiments of reusability confirmed the stability of the material. Its catalytic performance was restored after low-temperature pyrolysis. This research supports the use of endogenous nitrogen in biomass. It provides more options for advanced oxidation process application and marine resource development.

Mechanical activation to enhance the natural floatability of waste printed circuit boards.

The metal in the waste printed circuit boards (WPCBs) is an excellent secondary metal resource. WPCBs were ground to dissociate, and impurities in the dissociated product were removed by gradient flotation to recover valuable metals in this study. The effects of crushing methods on size composition and dissociation state of the crushed products were studied. Then the gradient flotation experiment was designed to verify the natural floatability of ground materials. Grinding test shows that impact crushing has greater grinding fineness (-0.074 mm) than shear crushing, which is 42.14% and 26.18% respectively with 5 min grinding. The flotation test results illustrate that the natural floatability of impurities increases with the grinding fineness, that is, the yield of floats increases without flotation reagents. For impact crushing and shear crushing, the floats yields are 38.48% and 31.75% respectively, accompanied by 70.53% and 65.46% impurity removal for ground materials with 5 min grinding. Subsequently, 21.61% and 26.35% of impurities can be further removed with the aid of collector. Finally, the recovery of Cu in concentrate reaches 67.84% and 65.75%, respectively. FT-IR proves that the excellent floatability of particles is caused by the significant hydrophobic group. Mechanical grinding has been proved to have double effects of improving dissociation and natural floatability.

Flotation dynamics of metal and non-metal components in waste printed circuit boards.

Flotation is an effective and clean separation technology to realize the recovery of metal in waste printed circuit boards (WPCBs). The flotation kinetic of metal and non-metal components was concerned in this study. In addition, the loading of bubbles, the collision and shedding of particles and bubbles were used to assist in proving the particle dynamics results. By analyzing the force on the particles, the load of bubbles on particles was analyzed, and the appropriate volume ratio of bubbles to particles was 1.5-8.0, depending on the particle density. Moreover, Clift model and Schiller-Naumann model has high fitting accuracy for the final bubble velocity. In addition, metal particles have greater settling velocity, which results in shorter collision time with bubbles. In the process of bubble-particle rising, the shedding probability gradually decreases, and the shedding probability of metal particles is much higher than that of non-metal particles. The results of flotation kinetics show that the removal of impurity particles represented by silicon mainly occurs in the initial stage of flotation process. The loss of copper increases with flotation time and collector dosage. This study reveals the flotation kinetics of particles from the perspectives of bubble loading, bubble-particle collision and shedding.

Recovery of metals in waste printed circuit boards by flotation technology with soap collector prepared by waste oil through saponification.

Recycling metal from waste printed circuit boards (WPCBs) through green flotation technology has been concerned in this paper. For the sake of environmentally friendly of flotation process, a renewable collector was prepared from waste oil by saponification reaction. The collector composition was analyzed by GC-MS, and results show that the main compositions are n-Hexadecanoic acid, oleic acid and octadecanoic acid. XRD and XRF results show that copper is the main valuable element for recovery. Effects of collector dosage and pH on flotation behavior were analyzed. In addition, the feasibility of improving copper recovery by multiple sorting test processes was also verified. Flotation results show that the concentrate yield and metal recovery decreases with the increase of collector dosage, accompanied by the increase of copper grade. When the dosage of collector is 3 kg/t, concentrate with 22% yield, 66% copper grade, and 47% copper recovery is obtained. Furthermore, concentrate yield and metal recovery rate first decrease and then increase with the increase of pH, while copper content first increase and then decrease. The suitable pH of the separation process is neutral environment (pH = 6-8). The study provides an alternative process for the recovery of metals in WPCBs.